Jump to content
  • Similar Content

    • By burnt_ends
      Hi, I followed the steps in this video
      https://www.youtube.com/watch?v=2Qm-nm4Z7wA&t=15s
      and I my brisket turned out dry and dense. I'm hoping you can tell me where I went wrong:
      - ~5.5 lbs (pre-trimmed) of Prime Angus grain fed brisket point from https://shalhoob.com/butcher-shop - trimmed as much of the silver skin off as I could - trimmed off hard fat and tried to leave 1/8" to 1/4" of fat - seasoned 24 hours prior to cook with 50/50 coarse black pepper and kosher salt - used Kamado Joe lump charcoal and two medium chucks of mesquite hardwood - ambient outside temperature was low-mid 80s - waited until grill came up to temp and smoke was mostly clear before putting meat on - put meat on fat side down - cooked in Classic III using sloroller, on the lower level rack - cooked with water pan on grill - used Thermopro two probe digital thermometer (1 probe at grill level, 1 probe in thickest part of brisket) - grill temp ranged between 245-270, but mostly 250-260 - took ~6.5 hrs to get to 170 internal temp - wrapped in foil at 172 - took ~1.5 hrs to get to 203  - at ~203 a wood shish kabob skewer did go through meat, but still felt a little resistance. At this point I pulled it b/c I was concerned about over cooking - kept in foil, wrapped in towel, put in cooler for 1.5 hrs
      The brisket had bark and a smoke ring. Pencil thin slice passed pull test. But it was dry and dense.  The attached photos are from the day after the cook and the meat is cold.
       
      Where do I go wrong?
       
      Thanks!!



    • By KamadoHop
      Thanks to @Kamadobjorn for the inspiration. The table is the “Applaro” Line. The hardware that you see in the last pictures all came from Hobby Lobby. The table comes with a thin, cheap pull bar and nothing else, not even knobs for the doors. The cooler pic is just for reference as that was what I was doing prior to getting the table. The last pic is sans hardware just the way it comes from IKEA. 
       
      I used Lenox 18TPI metal jigsaw blades with an adjustable speed jigsaw set to its lowest setting to cut the hole. I used this edge trim from Amazon: Trim
       
      If you have any other questions just ask. Cheers. 





    • By buckleybj
      I accidentally bought a two pack of bonless pork shoulder from Costco. I have always used bone-in, so this is new to me. As I was preparing the butts trimming sinew, silver skin, hard fat, veins etc, I started also cutting portions of the butts into sections. I now have two 4 lb boneless butts and several large scraps.
       
      This has provided me the opportunity to use the vertical spit I bought from Ceramicgrillstore.com a few months ago. I'm excited to say the least. 
       
      I'll post picture of the meal later this afternoon when I build it get it going. Here are pics of what I ended up with after trimming and then the portions I will smoke overnight for pulled pork tomorrow.
       
       


    • By Tiki Joe
      Hello,
      I just received a Pit Boss Kamado grill/smoker as a gift.
      I don't know the first thing about how to properly use it.
      I've been reading and viewing  a lot of info available on line, but I'm not seeing much for a novice like me.
      I will be firing it up tomorrow and start cooking.
      Does anyone have advice for a beginner?
    • By Big Biscuit
      Made some cod the other day on the KJ classic for me and my wife. It's a fairly simple and light meal for anyone watching their waistline. All I did was make two foil packets spray them down with some oil. Then I lined it with sliced onions, and tomatoes. After that I placed two pieces of cod loin which I've seasoned with some McCormick's Garden Vegetable on the veggies. Then tossed on some sliced lemons. Put them on the KJ and cooked till the cod hit an IT of 140°.
×
×
  • Create New...